update AQF10 carbon turnbuckles

Update AQF10

F103 type Driveshafts

hollow shaft












carbon shaft

titanium shaft









Send me an email @ aqdesign@live.nl if you want to purchase one off these shafts.

Update AQPro10

rolling chassis with undertray for batt support












rolling chassis without undertray












chassis without rear driveshaft
155gram











chassis with drive shaft
192gram

update AQF10

I ordered the front suspension from Tamiya F104 so i will fit this on my proto AQF10.
Also the Tubes dempers next to the main Shock will be replaced by mini shocks.
pictures will come soon.
for info please send an email to AQdesign@live.nl check youtube.com/aqdesign1980 for video updates

ProTen prototype

F103 carbon shaft

IN development carbon hollow en solid light weight axles for Tamiya F103 type

Kyosho Spada '09 electro & carbon conversion pictures

AQF10

Here is my new design. I used a 3mm thick zilver woven carbon plate 350mmx150mm
In the design I take out the t-bar principle like the Tamiya F103 in order 2 install Lipopack in the length for better weight distribution. The ESC en receiver on both sides.

F103 custom build project

So here it is. my first 1:10th Formule 1 race car

This car is completely build from aftermarket parts:

chassis +upperdeck Cross Racing
front suspension Cross Racing
upperdeck mount Cross Racing
batt mount Cross Racing
T-bar Cross Racing
High Speed bearings 9pcs Cross Racing
titanium turnbuckles Cross Racing
motorpod TRG
alu diff TRG
Diff mount + left wheel mount Tamiya
Thrust bearing Tamiya
Custom carbon shaft
16 titanium screws 2 lock alu parts
18 screws m3
2 screws m4
4 lockbolts m4
Slicks Type A Tamiya

electronics:

Lrp Spx
Lrp F1 Special Pro
Lrp VTEC 4600mah 4cells
Futuba mini digi servo
GM 2,4 ghz receiver

gears used:
104 spur x 25 pinion

over 85 km/u

R&M Custom Carbon Parts

full woven 3mm carbon fiber plates.

Kyosho inferno GT electro conversion full carbon fibre n titanium screws

Cross Fire Formule 1 2009 chassis build completely with aftermarket tunings parts.

my first build f1 chassis based on da f1 chassis from Cross Fire sith the TRG motorpod

R&M Customs Carbon Parts Introduction

Welcome 2 our blog

We are Ronald and Maurice from R&M Custom Carbon Parts from Eindhoven city, The Netherlands.

We build, create and drive RC model cars for over a decade now. And decided to do something with it. What we found is that da use of real carbon fibre plates would make a huge difference in driving and building experience than half carbon parts you get from your local store or even Internet shops. These aftermarket products which are often described as full carbon fibre isn't always what you think u gettin.

Kyosho Spada '09 electro conversion

So at first we started out with da brand new Spada '09 chassis, which is a nitro powered 12th scale 4wd drive with a body like the serpent 960 orso. What we have done is made a full carbon chassis plate and 2 parts which are bolted on the top of the front and rear suspension mounts. Not only did the weight decrease by a 3rd it also made da chassis much stiffer then before. Then we converted the nitro engine for a Electric engine. We used the LRP x12 6.5t which gives a lot off power to the four wheels. We haven't tested it yet with 7.4v lipo, it runs on 5cells GP 3600mah which will give it a topspeed of over 75km/h.

Kyosho inferno GT electro conversion

The second car is 8th scale Kyoscho inferno GT with the Aston Martin Lemans body. All the alu parts are now full carbon Fibre parts 3mm thick. We took of da nitro engine to fit a Speed Passion v10 5.5t electric engine with 14.8v lipo. We left the original brake intact so it wont have to stop on the engine. It now reaches topspeeds around 95+ km/h in less then 4 sec.


















all parts are now hand made but will be CNC cut for retail.

Footage is available on Youtube.

Parts will be available around august 2009.